INT FON PU 2K PCE TRA 03.79L ILV

ILVA Polimeri s.p.a. IC&S
Material Safety Data Sheet
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Product Number: TA 44 Product Name: Urethane, Clear Undercoat
Manufacturer: ILVA Polimeri s.p.a. Distributed by: I C & S
Phone Number: 0113902990991 1833 William Penn Way
Emergency Phone: 800-255-3924 Lancaster, PA 17601
Date Prepared: 9/01/06 717-391-6250
2. COMPOSITION/INFORMATION ON INGREDIENTS
OSHA ACGHI
Chemical Name CAS ppm TWA ppm TWA Weight %
Xylene 1330-20-7 100 100 36
Toluene 108-88-3 200 50 4
Methyl Ethyl Ketone 78-96-3 200 200 3.2
Butyl Acetate, iso 110-19-0 150 150 2.1
Propylene glycol monomethyl
ether acetate 108-65-6 N/EST N/EST 3.8
Ethylbenzene 100-41-4 100 100 4
3. HAZARDOUS IDENTIFICATION
Emergency Overview: WARNING! This product is extremely flammable.
POTENTIAL HEALTH EFFECTS
Inhalation: High gas, vapor, mist, or dust concentrations may be harmful if inhaled. May cause headache,
dizziness or nausea. May cause nose and throat irritation and possible lung injury.
Ingestion: May cause irritation of the mouth, throat and esophagus with nausea, abdominal discomfort,
vomiting, diarrhea and drowsiness.
Skin Contact: Prolonged exposure may cause skin irritation.
Signs And Symptoms Of Exposure: Shortness of breathing, confused behavior, redness of skin, swelling
of tissues, watery eyes, nausea.
4. FIRST AID MEASURES
Eye Contact: Immediately flush eyes with plenty of water, for at least 15 minutes. Get medical attention,
if irritation persists.
Inhalation: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give
oxygen. Get medical attention immediately.
Ingestion: If swallowed, do NOT induce vomiting. Give victim a glass of water or milk. Call a physician
or poison control center immediately. Never give anything by mouth to an unconscious person.
Skin Contact: Remove contaminated clothing, immediately wash skin thoroughly with plenty of soap and
water. If symptoms persist, seek medical attention.
Aggravated Medical Conditions: Skin and eye irritation.
ILVA Polimeri s.p.a. IC&S
Page 2 of 4
Product Number: TA 44 Urethane, Clear Undercoat
5. FIRE FIGHTING MEASURES
FLAMMABLE PROPERTIES
Flash Point: -4?C (25?F)
Flash Point Method: Tag Closed Cup
Auto ignition: N/A
LEL: 2.6
UEL: 12.8
Extinguishing Media: Use foam or dry chemical to extinguish fire.
Special Fire-Fighting Procedures: Firefighters should wear proper protective equipment and selfcontained
breathing apparatus with full-face piece in positive pressure mode. Move containers from fire
area if it can be done without risk. Use water to keep fire-exposed containers cool.
Unusual Fire And Explosion Hazards: Containers exposed to intense heat from fires should be cooled
with water to prevent vapor pressure buildup, which could result in container rupture. Container areas
exposed to direct flame contact should be cooled with large amounts of water.
Combustion Products: Fumes, smoke carbon monoxide and hydrocarbons.
6. ACCIDENTAL RELEASE MEASURES
Steps To Be Taken In Case Material Is Spilled Or Released: Ventilate area of leak or spill. Remove all
sources of ignition. Clean-up personnel require protective clothing and respiratory protection from vapors.
Cover the spill with sawdust, vermiculite, fuller's earth or other absorbent material. Place spilled material
and absorbent in a closed metal container. Dispose of all materials in accordance with applicable state and
federal regulations. Only specially trained or qualified personnel should handle the emergency.
7. HANDLING AND STORAGE
Precautions To Be Taken In Handling And Storage:
STORAGE TEMPERATURE: 64? to 75?F (18? to 25?C)
SHELF LIFE: 1 year @ 68?F (20?C)
SPECIAL SENSITIVITY: Heat, light, moisture.
PRECAUTIONS: Keep away from heat, sparks and open flame. Ground containers during
storage and transfer operations. Store in closed containers. Follow all MSDS/label precautions
even after container is emptied because they may retain product residues. Other Precautions: Empty containers retain product residue and can be dangerous. Do not pressurize, cut
weld, braze, solder, drill, grind, or expose such containers to heat, flame, sparks static electricity, or other
sources of ignition.
ILVA Polimeri s.p.a. IC&S
Page 3 of 4
Product Number: TA 44 Urethane, Clear Undercoat
8. EXPOSURE CONTROL / PERSONAL PROTECTION
PERSONAL PROTECTIVE EQUIPMENT
Respiratory Protection: Good industrial hygiene practice dictates that worker protection should
be achieved through engineering controls such as ventilation whenever feasible. When such
controls are not feasible to achieve full protection, the use of respirators and other personal
protective equipment is mandated. Before an air-purifying respirator can be used, air monitoring
must be performed to measure airborne concentrations of organic solvents. A NIOSH-approved
organic vapor respirator with dust, mist and fume filters is recommended. Observe OSHA
regulations for respirator use (29CFR 1910.1234).
Ventilation: Provide exhaust ventilation sufficient to keep the airborne concentration of this
product below its exposure limits. Exhaust air may need to be cleaned by scrubbers or filters to
reduce environmental contamination.
Protective Gloves: Nitrile rubber and PVC are not suitable protective materials; Neoprene is
recommended.
Eye Protection: Safety glasses with side shields (or goggles) and a face shield.
Other Protective Clothing or Equipment: Where splashing is possible, full chemically resistant
protective clothing (e.g., acid suit) and boots are required.
Work/Hygienic Practices: Use good personal hygiene when handling this product. Wash hands
thoroughly after handling this product.
Engineering Controls: Facilities storing or utilizing this material should be equipped with an
eyewash facility and a safety shower.
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance And Odor: Clear, colorless liquid with pungent odor.
Solubility In Water: Not soluble in most cases
Boiling Point: 79?C (174?F) VOC, Lbs./Gal.: 4.30
Vapor Pressure: 78.0 mm Hg @ 20?C VOC, Gr./L.: 515
Specific Gravity: 0.97 HAPS, Lbs./Gal.: 3.82
Pounds / Gallon: 8.09 HAPS, Gr./L: 457
Vapor Density: Heavier Than Air
Percent Volatile: 46.90
10. STABILITY AND REACTIVITY
Stability: Stable
Conditions To Avoid: Avoid high temperatures, heat, flame, and other sources of ignition.
Incompatibility: None Reported.
Hazardous Decomposition Or By Products: Carbon monoxide
Hazardous Polymerization: Will Not Occur
ILVA Polimeri s.p.a. IC&S
Page 4 of 4
Product Number: TA 44 Urethane, Clear Undercoat
11. TOXICOLOGICAL INFORMATION
Low order of toxicity
12. ECOLOGICAL INFORMATION
Environmental hazard
13. DISPOSAL CONSIDERATIONS
The preferred options for disposal are to send to licensed reclaimers, or approved incinerators.
Any disposal practice must be in compliance with federal, state, and local regulations. Do not
dump into sewers, ground, or any body of water.
14. TRANSPORT INFORMATION
DOT Class: Flammable Liquid.
Hazard Class: 3
UN No.: UN 1263
Packing Group: II
Guide No: 127
Ship Name: Paint
15. REGULATORY INFORMATION
OSHA STATUS: This product is hazardous under OSHA Standard 29 CFR
1910.1200.
TSCA STATUS: Ingredients of this product are on the TSCA inventory.
SARA TITLE III: Section 302: None.
Sections 311/312: Immediate & Delayed Health Hazard; Fire Hazard.
Section 313: Toxic Chemicals; Xylene CAS 1330-20-7; Toluene CAS 108-88-3; Methyl Ethyl Ketone CAS 78-93-3, Ethyl Benzene CAS100-41-4.
RCRA STATUS: Should be managed as a Hazardous Waste. (EPA Hazardous Waste No. D0001)
40 CFR 261.20-24
16. OTHER INFORMATION
HMIS INFORMATION:
Health: 2
Flammability: 3
Reactivity: 0
Protective: G
OTHER ADDITIONAL INFORMATION:
DISCLAIMER:
The information contained herein is based on the data available to us and is believed to be
accurate. However, no warranty is expressed or implied regarding the accuracy of this data or the
results to be obtained from the use thereof. We assume no responsibility

Product Datasheet